Specialized in the production and supply of a full range of aluminum profiles and metal fabrication
metal part
Metal Part vs. Sheet Metal Part
| Aspect | Sheet Metal Part | General Metal Part |
|---|---|---|
| Raw material | Flat metal sheet (coil or plate), typically thickness ≤ 6 mm | Can be sheet, bar, tube, profile, or even metal powder / liquid metal |
| Primary processes | Cutting, bending, stamping, welding, hemming, etc. | In addition to sheet metal processes: machining, casting, forging, powder metallurgy, additive manufacturing, etc. |
| Typical features | Uniform wall thickness, thin‑walled enclosures, brackets, housings | Solid or hollow, complex 3D shapes, thick or thin walls |
| Examples | Computer chassis, car doors, control cabinets, ventilation ducts | Gears, shafts, engine blocks, valves, tool handles, precision brackets |
Other Common Manufacturing Processes for Metal Parts
1. CNC Machining
- Milling: Removes material from a solid block to create complex shapes (pockets, curved surfaces, holes).
- Turning: Rotates the workpiece while a cutting tool shapes it – ideal for shafts, discs, threaded parts.
- Drilling, boring, reaming: Produces precise holes.
- Advantages: High accuracy (down to ±0.005 mm), wide material choice, suitable for low volumes and prototypes.
- Disadvantages: Significant material waste, cost increases with complexity.
2. Casting
- Sand casting: Uses sand molds – low cost, good for large or one‑off parts.
- Investment casting (lost‑wax): High precision, smooth surface – ideal for small, complex parts (e.g., turbine blades).
- Die casting: Injects molten metal into a steel mold under high pressure – very efficient for high‑volume aluminum or zinc parts (e.g., engine housings).
- Advantages: Can produce very complex internal and external shapes.
- Disadvantages: High tooling cost, possible internal defects like porosity.
3. Forging
- Shapes metal by hammering or pressing – refines grain structure, resulting in high strength.
- Typical parts: Connecting rods, crankshafts, wrenches, gear blanks – components subject to high stress.
- Advantages: Mechanical properties superior to cast or machined parts.
- Disadvantages: Expensive dies, limited shape complexity.
4. Powder Metallurgy (PM)
- Compacts metal powder into a shape, then sinters (bakes) it.
- Suitable for high‑volume production of small, complex, near‑net‑shape parts (gears, oil‑impregnated bearings).
- Advantages: High material utilization, can produce porous parts.
- Disadvantages: High equipment cost, part size limitations.
5. Metal Additive Manufacturing (3D Printing)
- Examples: SLM (Selective Laser Melting), DMLS – melts metal powder layer by layer.
- Ideal for complex internal cavities, lattice structures, custom parts (orthopedic implants, aerospace brackets).
- Advantages: Almost unlimited geometric freedom, minimal material waste.
- Disadvantages: Slow, expensive equipment and materials, surface finish generally rougher than machined parts.
How to Choose the Right Process?
| Consideration | Recommended Process |
|---|---|
| Thin‑walled, shell‑like, uniform thickness | Sheet metal fabrication |
| High precision, small batch, complex external shape | CNC machining |
| High volume, complex internal cavities, medium precision | Die casting or investment casting |
| High strength and fatigue resistance required | Forging |
| Very small, high volume, simple shape | Powder metallurgy |
| Extremely complex, custom, prototype | Metal additive manufacturing |
FAQs about Metal Parts Manufacturing (Covering Machining, Casting, Forging, Sheet Metal, etc.)
1. How do I choose the most suitable manufacturing process for my metal part?
Answer: It depends on part shape, volume, precision, material, and cost.
- Thin‑wall, enclosure → Sheet metal fabrication
- Complex external shape, high precision, low volume → CNC machining (milling/turning)
- Complex internal cavities, high volume → Die casting or investment casting
- High strength, impact resistance → Forging
- Very small, high volume, simple shape → Powder metallurgy
- Extremely complex internal geometry or custom parts → Metal additive manufacturing (3D printing)
2. What are the main differences between CNC machining and sheet metal fabrication?
Answer:
- Raw material: Machining starts from a solid block (bar, plate, billet) and removes material; sheet metal starts from a flat sheet and forms it by bending and cutting.
- Wall thickness: Machined parts can have varying wall thickness and solid features; sheet metal parts have essentially uniform wall thickness.
- Cost structure: Machining wastes more material but requires no dedicated tooling; sheet metal uses material efficiently, but complex shapes may need stamping dies.
- Typical parts: Machining → shafts, gears, brackets; sheet metal → enclosures, panels, chassis.
3. What are common DFM (Design for Manufacturing) mistakes in metal part design?
Answer:
- ❌ Ignoring material anisotropy (e.g., rolling direction affects bending or strength)
- ❌ Designing impossible deep cavities or extremely small internal radii (end mills have a radius; EDM or casting can work but at higher cost)
- ❌ Not accounting for heat‑treatment distortion → needs stock allowance or process sequence changes
- ❌ Varying wall thickness in a sheet metal part → cannot be made from a single sheet
- ❌ Weld design without considering access → welding torch cannot reach
- ❌ Applying tight tolerances to all dimensions → significantly increases cost; only tight on mating features
4. When is metal additive manufacturing (3D printing) more economical than traditional processes?
Answer:
- The part has extremely complex internal channels or lattice structures that are impossible or very costly to make conventionally.
- Low volume (1–50 pieces) and no tooling required, especially when die/mold cost is high.
- Rapid iteration is needed (prototypes).
- Material utilisation is critical (e.g., titanium powder is expensive, but conventional milling might waste 90% of the material).
- Not suitable for: high‑volume simple shapes, parts requiring very high surface finish or extremely tight tolerances (3D printed parts often need post‑machining).
5. How can I control the cost of machined parts?
Answer:
- Reduce set‑up changes: Design features that can be machined in one set‑up.
- Avoid overly tight tolerances: Relax tolerances on non‑critical surfaces.
- Simplify geometry: Avoid deep narrow slots that require special long, small‑diameter tools.
- Choose free‑machining materials: e.g., 1215 steel, 6061 aluminium – easier to machine than stainless 304 or Inconel.
- Design generous fillets: Internal fillet radius should not be smaller than common tool diameters (suggest R ≥ 1 mm or R ≥ 2 mm).
- Combine parts: Integrate multiple functions into one machined part to eliminate assembly.
6. What are common casting defects and how can they be avoided?
Answer:
- Porosity: Gas trapped in the melt → improve venting and degassing.
- Shrinkage cavity / porosity: Insufficient feed metal during solidification → optimise gating system, add risers.
- Cold shut: Incomplete fusion of metal streams → increase pouring temperature or speed.
- Sand inclusion: Sand from the mold breaking loose → improve mold strength.
- Dimensional deviation: Incorrect shrinkage allowance → correct die dimensions, perform trial casting.
- Design rule: Avoid abrupt wall thickness changes, use radiused transitions, and allow machining stock.
7. What performance advantages does forging have over casting or machining?
Answer:
- During forging, metal grains follow the contour of the part (directional grain flow), and the grain lines are not cut. Therefore:
- Strength (especially fatigue strength) and toughness are significantly higher than cast or machined‑from‑bar parts.
- Very few internal defects (porosity, shrinkage).
- Suitable for parts subject to impact or cyclic loads: connecting rods, crankshafts, gear blanks, helicopter rotor hubs.
- Disadvantages: Expensive dies, limited shape complexity, uneconomical for low volumes.
8. How do I select the right surface finish for my metal part?
Answer: Choose according to functional requirements.
| Requirement | Recommended Finish | Suitable Materials |
|---|---|---|
| Rust protection (indoor) | Painting, powder coating, zinc plating | Carbon steel |
| Rust protection (outdoor / corrosive) | Hot‑dip galvanizing, stainless steel itself, passivation | Carbon steel, stainless steel |
| Wear resistance | Hard chromium plating, nitriding, quenching | Steel, aluminium (hard anodizing) |
| Electrical conductivity / solderability | Tin plating, silver plating, electroless nickel plating | Copper, aluminium, steel |
| Decorative appearance | Brushing, polishing, anodizing (dyed) | Aluminium, stainless steel, brass |
| Low friction (self‑lubricating) | PTFE coating, phosphating + oil | Steel |
9. How should I manage tolerances for metal parts to ensure proper assembly?
Answer:
- Perform tolerance stack‑up analysis to calculate worst‑case clearance or interference.
- Distinguish functional dimensions from non‑functional dimensions: apply tight tolerances (e.g., IT6–IT8) only to mating features; relax others.
- Use datums: design, machining and inspection datums should be consistent.
- Consider process capabilities:
- Turning / milling: economical tolerance ±0.025 mm to ±0.05 mm
- Sheet metal bending: ±0.3 mm
- Die casting: ±0.1 mm (small parts) to ±0.5 mm (large parts)
- Investment casting: ±0.1 mm to ±0.3 mm
- For interference or sliding fits, consult standard tolerance tables (e.g., ISO 286, GB/T 1800).
10. How can I produce small‑batch metal parts (1–100 pieces) quickly and at low cost?
Answer:
- First choice: CNC machining – no tooling, wide material choice, fast lead time (days).
- Use online manufacturing platforms (Protolabs, Xometry, Hubs) – instant quotes, easy ordering.
- Consider sheet metal – if the part is a thin‑shell enclosure, laser cutting + bending is very fast.
- Avoid opening a die – die/mold costs cannot be amortised for low volumes (unless die casting or forging is absolutely required).
- Metal 3D printing – for extremely complex geometry, but per‑part cost is still higher than machining.
- Semi‑finished stock: Buy near‑net shapes like bar, profile or tube, and machine only a small amount (e.g., make a wrench from hex bar).
- Combine processes: e.g., laser‑cut contour + subsequent drilling/tapping + manual bending.